| Author |
 Topic  |
|
|
Rapchizzle
Senior Member
3676 Posts |
 Posted - 03/10/2012 : 11:47:23 AM
|
I have tried searching but was not able to get it to work. I'm looking to find out who in Charleston has the best prices on marine plywood. I'm looking for the prices of 1/4" (6mm), 3/8" (9mm) and 1/2" (12 mm).
-Capt. Chris Rapchick
yella bote
no motor |
|
|
mrhardware
Senior Member
569 Posts |
Posted - 03/10/2012 : 1:33:32 PM
|
Try
Buck Lumber 795-0150 James Island
Guy C Lee 884-3131 Mt Pleasant
Southern Lumber 744-6281 Charleston
If they don't have it they can get it quickly.
Tell 'em Mr Hardware sent you
Mr Hardware |
Edited by - mrhardware on 03/10/2012 1:34:14 PM |
 |
|
|
Cracker Larry
Senior Member
1455 Posts |
Posted - 03/10/2012 : 6:27:30 PM
|
If any of those places can supply BS1088 meranti or okume mahogany at a reasonable price, I'd be surprised. Pressure treated pine or fir is not marine plywood. Charleston used to have a couple of good sources for marine mahogany, but they closed in the boat building recession.
Shipping charges are cheap compared to the material and labor of building a boat. Get the absolute best. It's only $100 shipping charge from south Florida to Savannah, doesn't matter if it's 1 sheet or 20, and you will need close to 20 sheets for that boat. Shipping to Charleston would be about the same. If this is for the boat you were talking of building, don't cut corners here. A hundred bucks is only a rod holder or 2, versus the core of your boat
Capt. Larry Teuton
Cracker Built Custom Boats |
Edited by - Cracker Larry on 03/10/2012 6:38:01 PM |
|
|
|
spareparts
Senior Member
931 Posts |
Posted - 03/12/2012 : 10:01:18 AM
|
| Check with Mark Bayne @ Sea Island Boat Works, you may be able to piggy back on one of his shipments http://www.seaislandboatworks.com/ On their site it says they stock okume Rap, check the past projects on his site, there are a couple on there that might grab your attention |
Edited by - spareparts on 03/12/2012 10:05:43 AM |
|
|
|
Capt. Pluffmudd
Captain
159 Posts |
Posted - 03/12/2012 : 4:01:06 PM
|
They sell it at Charleston Marine Lumber yard. It is up at the old navy base right next to Detyen's ship yard.
Get It! |
|
|
|
cferebee01
Starting Member
1 Posts |
Posted - 03/13/2012 : 12:10:12 PM
|
Try World Panel Products FLA-888-836-3379 NC-866-364-0500quote:
Originally posted by Rapchizzle
I have tried searching but was not able to get it to work. I'm looking to find out who in Charleston has the best prices on marine plywood. I'm looking for the prices of 1/4" (6mm), 3/8" (9mm) and 1/2" (12 mm).
-Capt. Chris Rapchick
yella bote
no motor
|
|
|
|
HereFishyFishy
Intermediate Member
51 Posts |
Posted - 03/22/2012 : 2:34:04 PM
|
quote:
Originally posted by spareparts
Check with Mark Bayne @ Sea Island Boat Works, you may be able to piggy back on one of his shipments http://www.seaislandboatworks.com/ On their site it says they stock okume Rap, check the past projects on his site, there are a couple on there that might grab your attention
I'll 2nd Mark @ Sea Island Boat Works. I too searched all over Charleston and he had the best I could find local.
---------------------------
2006 1720 Key West |
|
|
|
Cracker Larry
Senior Member
1455 Posts |
Posted - 03/22/2012 : 4:04:33 PM
|
quote:
They sell it at Charleston Marine Lumber yard. It is up at the old navy base right next to Detyen's ship yard.
I used to buy from there occasionally, but they went out of business a couple of years ago, unless they have re-opened since?
Capt. Larry Teuton
Cracker Built Custom Boats |
|
|
| |
Topic |
|
Marine plywood in/around Charleston
